Cabletron Systems Access Server 316 Guide d'installation Page 255
- Page / 302
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
23-7
Messages 600 – 699
Local -657- Permanent database inaccessible at this moment
Explanation: You attempted to use the DEFINE or CHANGE command with an SNMP
characteristic, but the permanent database could not be accessed due to conflicting access
requests.
Action: Try again later.
Local -658- No resources available at this moment
Explanation: The access server could not complete the SNMP operation due to
inadequate memory availability.
Action: Verify the access server memory usage. See the section Verify Access Server
Memory Usage (Chapter 2).
Local -659- Community name does not exist
Explanation: You attempted to use the CLEAR or PURGE command with a community
name that has not been previously set or defined.
Action: Use the SHOW/MONITOR/LIST SNMP command to view the currently
specified community names.
Local -660- Community data lost, SNMP reset to factory defaults
Explanation: SNMP information has been reset to factory defaults and SNMP
information you have modified has been lost. This can occur if you pressed the reset
button while installing new software or if the SNMP portion of the permanent database is
corrupted (hardware error).
Action: Reset and/or redefine your SNMP community data. If this action fails to correct
the problem, the access server memory that stores the SNMP characteristics is faulty.
Refer to Chapter 29 for service information.
Local -662- No resources - SNMP not enabled
Explanation: The access server could not enable SNMP on the access server due to
inadequate memory availability.
Action: Verify the access server memory usage. See the section Verify Access Server
Memory Usage (Chapter 2).
Local -663- No Internet address - SNMP not enabled
Explanation: You entered a command that cannot be performed until you set the access
server’s Internet address.
Action: Set the Internet address. See the section Verify Internet Address (Chapter 3).
- DECserver 1
- Network Access Software 3
- Problem Solving Guide 3
- Web site: www.dnpg.com 4
- Contents 5
- Chapter 4 SLIP/PPP Problems 6
- Chapter 14 IPX Problems 11
- Chapter 18 Messages 000 – 099 12
- Chapter 26 Messages 900 – 999 14
- Chapter 29 Service Guidelines 14
- Typographical Conventions 16
- Associated Documents 17
- Software WWENG2 MNENG2 WWENG2 20
- Image(s) MNENG3 20
- Verify the Load Host 21
- At an OpenVMS load host: 23
- $ MCR NCP 26
- Downline Load Request Failure 27
- Is Defined Correctly 28
- Messages 29
- $ RUN SYS$SYSTEM:LATCP 33
- Local> SHOW MEMORY STATUS 36
- Low Pool Size: 52480 bytes 36
- Low Pool Used: 1940 bytes 36
- Verify Service Rating 39
- Telnet Resource Problems 43
- Verify Internet Host Name 45
- Telnet Client Hung 50
- SLIP/PPP Problems 55
- SLIP Connection Problems 57
- Verify SLIP Host Address 58
- PPP Connection Problems 65
- Failure Reasons 69
- AppleTalk Access Problems 71
- 3. AppleTalk Gateway Route 72
- Verify AppleTalk Is Enabled 73
- Verify AppleTalk State Is Up 73
- Verify Cache Size Is Correct 74
- Verify Attached Host Software 75
- Local> SHOW PORT 1 ATCP 76
- Local> SHOW PORT 1 76
- Performance Problems 77
- AppleTalk Gateway Route 78
- SNMP Access Problems 79
- Verify SNMP Enabled 82
- Verify Network Configuration 84
- MIB Information 85
- (NMS), do the following: 87
- Reported 89
- Access Problems 91
- TN3270 Connection Problems 92
- Verify TN3270 Keyboard Maps 94
- Telnet Negotiations Problems 97
- Procedure 101
- Authentication Protocol 102
- Overview 109
- Introduction 110
- Verify Internet Address 110
- Local> SHOW SERVER STATUS 111
- Console Port Problems 112
- Problems 113
- Port and Device Problems 114
- Solution 115
- Verify the Port Configuration 127
- Test the Printer Port 128
- LAT Printing Problems 131
- Verify the Print Queue 133
- Verify LAT Group Codes 136
- Telnet Printing Problems 138
- Connection 143
- Listener 145
- Echoes or Double Lines 148
- Modem Configuration Problems 149
- Dial-In User Procedure 151
- Access Server 154
- Not Respond 158
- Does Not Respond 161
- IPX Problems 165
- Network Access Software 167
- Management Guide 167
- Server Port 168
- Accounting Problems 171
- Problems with Accounting Log 172
- Verify Server Console Port 175
- Remote Login Problems 177
- Rlogin Connection Problems 178
- Verify Rlogin Server Username 183
- More Information 185
- Rlogin Client Hung 186
- Suspend IO Sequence 187
- Properly 188
- Some Applications 189
- Directed TFTP Problems 191
- Incorrect Filename 194
- Action: None 197
- >>> b eth:mneng2 197
- Messages 000 – 099 199
- Messages 200 – 299 201
- Corrupted solicit request 209
- Messages 300 – 399 211
- Messages 400 – 499 227
- (Chapter 3) 232
- Messages 500 – 599 243
- Local> INITIALIZE 244
- Messages 600 – 699 249
- Messages 700 – 799 257
- (Chapter 2) 269
- Messages 800 – 899 271
- (Chapter 272
- Messages 900 – 999 279
- Messages 1000 – 1099 291
- Messages 1100 – 1208 293
- Service Guidelines 299
- What To Do 300
- Digital Networks 302
Produits connexes et manuels pour Mise en réseau Cabletron Systems Access Server 316
(60 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.435 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels