Cabletron Systems CSX400-DC Guide de l'utilisateur Page 93
- Page / 275
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CSX400 Configuration with QuickSET
CSX400 and CSX400-DC User’s Guide 79
Wide Area 1 and 2 Configuration
Refer to the appropriate section listed below to configure your Wide Area 1 or 2 interface on the
CSX400:
Wide Area T1 Configuration Window
Wide Area E1 Configuration Window
Wide Area DI Configuration Window
Wide Area Synchronous Configuration Window
Wide Area DDS Configuration Window
Wide Area HDSL Configuration Window
NOTE
When configuring WAN interfaces 1 and 2 with
QuickSET
, the Wide Area configuration
window that displays corresponds to the specific WPIM that is installed into the
CSX400.
NOTE
Configuration for the Wide Area 2 interface is the same as the configuration for the
Wide Area 1 interface.
Both Wide Area 1 and Wide Area 2 slots must be populated to initiate Wide Area
interface 2 configuration.
- CSX400 AND CSX400-DC 1
- USER’S GUIDE 1
- FCC Notice 3
- DOC Notice 3
- DECLARATION OF CONFORMITY 6
- Contents 14
- Introduction 15
- Document Conventions 17
- Getting Help 18
- About the CSX400 19
- Ethernet LAN Connection 21
- Optional Features 22
- CSX400 Firmware Support 22
- WAN Protocols 23
- Firmware Data Compression 24
- Inverse Multiplexing (IMUX) 24
- DHCP and NAT 25
- Point-to-Point Protocol (PPP) 26
- PAP and CHAP Security 26
- Multilink Protocol 27
- Telephone Switch Support 28
- ISDN Back-up 29
- Bridging and Routing 30
- System Passwords 32
- SNMP MIB Support 33
- Cabletron Enterprise MIBs 34
- SNMP Trap Support 34
- Arranging ISDN Service 37
- ISDN BRI Line Configuration 38
- ISDN BRI Configurations 39
- Telephone Switch Parameters 40
- Collect Network Information 44
- Names and Passwords 44
- ISDN Line Information 45
- Network Information Diagrams 46
- Network Information Tables 52
- Sample Configuration 56
- Names and Passwords Example 61
- Ethernet Cabling Requirements 63
- 10BASE-T Twisted Pair Network 64
- Multimode Fiber Optic Network 65
- 10BASE2 Coaxial Cable Network 67
- Transceiver Requirements 67
- Installation 69
- Installing Interface Modules 70
- ETHERNET 1 71
- ETHERNET 2 71
- Removing the CSX400 Cover 72
- Removing the CSX400-DC Cover 73
- CSX-COMP/ENCR Installation 76
- Installing the CSX400 77
- Tools Required 78
- Rackmount Brackets (2) 79
- Screws (4) 80
- Rackmount 80
- Brackets (2) 80
- DC Input Power Strip 84
- 48 or 60 Vdc 84
- Power Source 84
- CSX400 configuration 87
- Ethernet Configuration 88
- QuickSET 114
- Firewall Configuration Window 115
- Routing Configuration Window 121
- IP Routing Configuration 122
- IPX Routing Configuration 122
- Host Map Window 123
- Figure 43 Redirector Window 126
- QuickSET Pull-Down Menus 131
- Firmware Upgrade Menu 133
- Advanced Configuration Menu 136
- Management 139
- Local Management Overview 140
- COMMAND FIELDS 141
- DISPLAY FIELDS 141
- INPUT FIELDS 141
- SELECTION FIELDS 141
- EVENT MESSAGE FIELD 141
- Accessing Local Management 146
- Main Menu Screen 147
- Setup Menu Screen 148
- System Level Screen 149
- Setting the System Date 152
- Setting the System Time 152
- Setting the Host IP Address 153
- Setting the Subnet Mask 153
- Setting the Default Gateway 153
- Setting the Default Interface 154
- SNMP Community Names Screen 155
- Setting SNMP Community Names 156
- SNMP Traps Screen 157
- Flash Download Screen 159
- RUNTIME Download 161
- BOOTPROM Download 161
- Bridge Setup Screen 163
- Bridge_Port 164
- Router Setup Screen 166
- IP Configuration Screen 167
- IP General Config Screen 168
- IPX Configuration Screen 176
- Entering the IPX Address 179
- IPX Routing over Frame Relay 181
- Enabling RIP on a Port 184
- WAN Setup 186
- MIB Navigator 191
- MIB Navigator Screen 192
- Navigation Commands 195
- MIBNav-> ctron 196
- MIBNav-> next /1/3/6/1/2/1 198
- MIBNav-> pwd 198
- Other Commands 204
- MIBNav-> done 217
- Connection closed 217
- Troubleshooting 219
- Troubleshooting the LAN 222
- Troubleshooting the WAN 223
- Status 1 (STS1) LED is RED 224
- Status 1 (STS1) LED is AMBER 225
- Status 1 (STS1) LED is GREEN 225
- Status 2 (STS2) LED is OFF 226
- Status 2 (STS2) LED is AMBER 227
- Status 2 (STS2) LED is GREEN 227
- WPIM-HDSL Installed in CSX400 228
- WPIM-S/T Installed in CSX400 228
- If Bridging 229
- If TCP/IP Routing 229
- EPIM-F1 and EPIM-F2 232
- Connector Type 235
- Grounding 235
- EPIM-A and EPIM-X (AUI Port) 236
- WPIM Cable Specifications 237
- WPIM Cable Specifications 238
- WPIM-SY interface cables 239
- WPIM-SY 239
- WPIM-DDS 247
- WPIM-DI interface cables 250
- WPIM-HDSL 251
- WPIM-S/T 252
- TELECOM — FCC Part 68, CS-03 255
- Glossary 265
- POWER SUPPLY CORD 275
- GERMAN: 275
- SPANISH: 275
Produits connexes et manuels pour Mise en réseau Cabletron Systems CSX400-DC
(178 pages)
(87 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels