Cabletron-systems 9F310-02 Manuel d'utilisateur

MMAC-Plus ™ 9F310-02 & 9F315-02FDDI Switch ModuleUser’s Guide

Introduction1-2 interfaces provide frames filtered, frames forwarded, and all Spanning Tree Protocol parameters. The 9F310-02 and 9F315-02 modules sup

1-3Features Figure 1-1. The 9F310-02 and 9F315-02 ModulesMMAC PLUSMMAC PLUSMMAC PLUSMMAC PLUS

Introduction1-4 Related Manuals The manuals listed below should be used to supplement the procedures and technical data contained in this manual. MMA

2-1 Chapter 2 Installing the MMAC-Plus modules The 9F310-02 and 9F315-02 modules occupy two slots in the MMAC-Plus chassis. The modules must be insta

Installing the MMAC-Plus modules2-2 Figure 2-1. Installing the 9F310-02 and 9F315-02 Modules7FLNK8FLNKFLNK10FLNKINS11FLNKINS12RXTXRXTXRXCircuit CardC

2-3The Reset Switch The Reset Switch The Reset switch is located on the rightmost front panel, under the top plastic tab as shown in Figure 2-2. It s

Installing the MMAC-Plus modules2-4 User Accessible Components Figure 2-3 shows the various components that are accessible to the user. These consist

2-5User Accessible Components See the Cautions at the end of this table. Table 2-1. Function of DIP Switch SwitchFunction Description 8Clear Passwo

Installing the MMAC-Plus modules2-6

3-1 Chapter 3 Operation The 9F310-02 and 9F315-02 modules are capable of bridging/switching any three, of five possible interfaces, depending on how i

Operation3-2 System Management Buses There are two management channels within the MMAC-Plus system: the SMB-1 and the SMB-10. These buses provide out

3-3DC/DC Converter DC/DC Converter The DC/DC converter converts the 48 VDC on the system power bus to the necessary operating voltages for its host n

Operation3-4 The Host engine sends and receives packets via the CPU FPS Interface. This allows the bridge to perform spanning tree protocol and other

4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs indicate the status of the module and may be used as an aid in trouble shooting. Shown in Fig

LANVIEW LEDs4-2 The function of the two System Status LEDs, System Management Bus (SMB) and the CPU, are listed in Table 4-1.The function of the INB

4-3 The function of the FDDI receive LEDs are listed in Table 4-4.The function of the FDDI transmit LEDs are listed in Table 4-2.The FDDI status LEDs

LANVIEW LEDs4-4The functions of the FDDI Status LEDs are listed in Table 4-6.Table 4-6. FDDI Status LEDs A P S B STATEGreen N/A N/A Green P

5-1Chapter 5SpecificationsTechnical SpecificationsCPU:Intel i960 RISC based microprocessorMemory:4 Meg. Local RAM (expandable to 12 Meg.)2 Meg. Flash Me

Specifications5-2SafetyThis equipment meets the safety requirements of:• UL 1950• CSA C22.2 No. 950 • EN 60950• IEC 950• EMI Requirements of FCC Part 1

5-3Link Distance9F310-02Up to 2 kilometers on multimode fiber-optic cable as specified by ANSI MMF-PMD.9F315-0240 kilometers (max), 25 kilometer (typica

i Notice Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior

Specifications5-4

ii Notice FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may no

vNotice Safety Information CLASS 1 LASER TRANSCEIVERSThe 9F315-02 is a Class 1 Laser ProductThe 9F315-02 uses Class 1 Laser transceivers. Read the fo

Noticevi Safety Information CLASS 1 LASER TRANSCEIVERSLaser Radiation and Connectors When the connector is in place, all laser radiation remains with

vii Contents Chapter 1 Introduction Features...

Contentsviii

1-1 Chapter 1 Introduction The 9F310-02 and 9F315-02 are three port switch modules with two front panel FDDI interfaces and one INB-1 backplane inter