CTP100TCOAXIAL TO TWISTED PAIR 10BASE-T MEDIA ADAPTERUSER’S MANUAL CABLETRON SYSTEMS, P. O. Box 5005, Rochester, NH 03866-5005
CHAPTER 1: INTRODUCTION Page 1-4 CTP100T USER’S MANUAL 1.3.2 Distance and Cable Type The CTP100T adapter supports an unshielded twisted pair (UTP)
An Overview of the CTP100T AdapterCTP100T USER’S MANUAL Page 1-5 1.3.5 LANVIEW LEDs The CTP100T adapter has five LANVIEW LEDs that monitor network
CHAPTER 1: INTRODUCTION Page 1-6 CTP100T USER’S MANUAL 1.3.6 Application The CTP100T adapter can be used with any of Cabletron Systems 10BASE-T co
An Overview of the CTP100T AdapterCTP100T USER’S MANUAL Page 1-7 This provides the ability to use an existing thin-net coaxial segment, or add a th
CHAPTER 1: INTRODUCTION Page 1-8 CTP100T USER’S MANUAL 1.4 Related User Manuals Other Cabletron Systems manuals (not supplied with the CTP100T ada
CTP100T USER’S MANUAL Page 2-1 CHAPTER 2INSTALLATION REQUIREMENTS This chapter lists the hardware and network requirements to ins
CHAPTER 2: INSTALLATION REQUIREMENTS Page 2-2 CTP100T USER’S MANUAL Insertion Loss - The maximum insertion loss allowed for a 10BASE-T link is 11
Network Design GuidelinesCTP100T USER’S MANUAL Page 2-3 Temperature - Most multi-pair PVC 24 AWG twisted pair cables typically have an attenuation
CHAPTER 2: INSTALLATION REQUIREMENTS Page 2-4 CTP100T USER’S MANUAL • On a thin-net cable segment, the male end of the segment connects to the CTP
CTP100T USER’S MANUAL Page 3-1 CHAPTER 3INSTALLATION This chapter describes how to connect the CTP100T adapter to your network. E
CTP100T USER’S MANUAL i NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this docume
CHAPTER 3: INSTALLATION Page 3-2 CTP100T USER’S MANUAL 3.2 Installation If the CTP100T adapter is going to be mounted on a flat surface, pro-ceed
InstallationCTP100T USER’S MANUAL Page 3-3 5. Attach the CTP100T adapter to the Velcro mount.6. Proceed to Section 3.2.2 to complete the CTP100T ad
CHAPTER 3: INSTALLATION Page 3-4 CTP100T USER’S MANUAL➊ Twisted Pair Segment ➏ Thin-net Segment➋ RJ45 Port ➐ BNC Port➌ Power Receptacle ➑ Terminati
InstallationCTP100T USER’S MANUAL Page 3-56. Check that the PWR LED of the CTP100T adapter ➒ is on. This indicates that the unit is receiving power.
CHAPTER 3: INSTALLATION Page 3-6 CTP100T USER’S MANUALe. Reconnect the RJ45 connector to the RJ45 port ➋. If a link has not been established, contact
CTP100T USER’S MANUAL Page 4-1CHAPTER 4TESTING AND TROUBLESHOOTINGThis chapter contains procedures to check that the RJ45 adapter
CHAPTER 4: TESTING AND TROUBLESHOOTING Page 4-2 CTP100T USER’S MANUAL➊ LAN-MD ➎ CTP100T Adapter➋ AUI Cable ➏ Thin-net Coax Segment➌ 10BASE-T Twisted
Installation CheckoutCTP100T USER’S MANUAL Page 4-34. If you have not already attached a thin-net segment ➏ to the BNC port of the CTP100T adapter ➎
CHAPTER 4: TESTING AND TROUBLESHOOTING Page 4-4 CTP100T USER’S MANUAL4.2 Using LANVIEWThe CTP100T adapter uses Cabletron Systems built-in visual diag
Using LANVIEWCTP100T USER’S MANUAL Page 4-5Link OK (LNK) LEDWhen this green LED is on, a link has been established between the CTP100T adapter and t
ii CTP100T USER’S MANUAL FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) th
CHAPTER 4: TESTING AND TROUBLESHOOTING Page 4-6 CTP100T USER’S MANUALCollision Present (CLN) LEDThis red LED flashes when the CTP100T adapter detects
CTP100T USER’S MANUAL Page A-1APPENDIX ASPECIFICATIONSThis appendix provides the specifications for the CTP100T adapter.A.1 Interf
APPENDIX A: SPECIFICATIONS Page A-2 CTP100T USER’S MANUALA termination switch on the CTP100T can be used to provide an internal 50-ohm termination at
Environmental SpecificationsCTP100T USER’S MANUAL Page A-3A.4 Environmental SpecificationsSafetyThe CTP100T adapter meets the safety requirements of
APPENDIX A: SPECIFICATIONS Page A-4 CTP100T USER’S MANUALA.6 Physical SpecificationsCTP100T adapter Height: 8.38 cm (3.3 in)Width: 13.46 cm (5.3 in
CPT100T USER’S MANUAL iii VCCI NOTICE This equipment is in the 1st Class Category (information equipment to be used in commercial and/or industrial a
CTP100T USER’S MANUAL v TABLE OF CONTENTS CHAPTER 1 INTRODUCTION 1.1 Who Should Use This Manual...
TABLE OF CONTENTS vi CTP100T USER’S MANUAL APPENDIX A SPECIFICATIONS A.1 Interface Connectors...
CTP100T USER’S MANUAL Page 1-1 CHAPTER 1INTRODUCTION Welcome to the Cabletron Systems CTP100T Coaxial to Twisted Pair 10BASE-T
CHAPTER 1: INTRODUCTION Page 1-2 CTP100T USER’S MANUAL 1.2 Structure of This Manual This manual is organized as follows:Chapter 1, Introduction ,
An Overview of the CTP100T AdapterCTP100T USER’S MANUAL Page 1-3 ➊ Power Receptacle ➍ Termination Switch ➋ RJ45 Port ➎ BNC Port ➌ LANVIEW LED
Commentaires sur ces manuels