Cabletron Systems EFDMIM Guide d'installation

MMAC-M8FNB™MULTI-MEDIA ACCESS CENTEROVERVIEW AND SETUP GUIDE CABLETRON SYSTEMS, P.O. Box 5005, Rochester, N.H. 03866-5005

INTRODUCTION Page 1-2Chapter 3, MMAC-M8FNB Setup , contains instructions for rack mounting your MMAC-M8FNB, inserting the fan tray, installing the p

INTRODUCTION Page 1-3 modules into the MMAC-M8FNB, how to attach cable segments to the modules, and how to test those segments after they have been i

INTRODUCTION Page 1-4By Internet mail: [email protected] FAX: (603) 337-3075By BBS: (603) 335-3358 (4 lines available) 1.4 THE MMAC-M8FNB MULTI MED

INTRODUCTION Page 1-5A variety of IEEE 802.3, IEEE 802.5, and FDDI compliant media can be connected to the MMAC-M8FNB, including shielded and unshiel

INTRODUCTION Page 1-6short circuit protection); or excess output voltage (over voltage protection). The power supply will automatically recover when

INTRODUCTION Page 1-7Any two matching power supply modules (i.e., two M8PSMs, two M8PSM-Es, or two M8PSM-EDCs) will use a current sharing scheme such

INTRODUCTION Page 1-8 Remote Management The remote management capability built in to the M8PSM-E and -EDC allows the network manager to determine whe

INTRODUCTION Page 1-9 Removable Fan Tray The MMAC-M8FNB is equipped with a removable fan tray, which means that you can replace a failed fan unit qui

INTRODUCTION Page 1-10

Page 2-1 CHAPTER 2INSTALLATION REQUIREMENTS AND SPECIFICATIONS This chapter describes the following:• Site guidelines that must be met before install

INSTALLATION REQUIREMENTS AND SPECIFICATIONS Page 2-2 cooling within the rack, there must be 7.6 cm (3 in.) of clearance above the unit and 5 cm (2 i

INSTALLATION REQUIREMENTS AND SPECIFICATIONS Page 2-3 2.3 OPERATING SPECIFICATIONS The following lists the specifications for the MMAC-M8FNB enclosure

INSTALLATION REQUIREMENTS AND SPECIFICATIONS Page 2-4 2.3.2 Power Supply Requirements M8PSM The M8PSM power supply senses and automatically adapts t

INSTALLATION REQUIREMENTS AND SPECIFICATIONSPage 2-5plug on the other end which is suitable for the use and application of the product and that is app

INSTALLATION REQUIREMENTS AND SPECIFICATIONSPage 2-6The mains cord used with this equipment must be a two-conductor- plus-ground type with minimum 1 m

INSTALLATION REQUIREMENTS AND SPECIFICATIONSPage 2-7These units are intended for indoor use only, and must be used with a user-supplied two-conductor-

INSTALLATION REQUIREMENTS AND SPECIFICATIONSPage 2-82.4 LEDsPower OK When lit, this green LED indicates that the(Power Supply) power supply module is

INSTALLATION REQUIREMENTS AND SPECIFICATIONSPage 2-9Figure 2-1. The M8PSM, M8PSM-E, and M8PSM-EDCM8PSM100 - 125 ~ 8A200 - 250 ~ 5A50/60 Hz+5 VOLT TEST

INSTALLATION REQUIREMENTS AND SPECIFICATIONSPage 2-10Power Fail When lit, this red LED indicates a loss of input(Power Supply) power, loss of regulati

INSTALLATION REQUIREMENTS AND SPECIFICATIONSPage 2-11Fan A green LED indicates that all fans inside the (E-series only) M8PSM-E or -EDC module are ope

i NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice.

INSTALLATION REQUIREMENTS AND SPECIFICATIONSPage 2-122.5 SAFETYDesigned in accordance with UL1950, CSA C22.2 No. 950, IEC950, and EN 60950. Meets the

Page 3-1CHAPTER 3MMAC-M8FNB SETUPThis chapter contains instructions to help you set up Cabletron Systems’ MMAC-M8FNB. You will not need any special to

MMAC-M8FNB SETUPPage 3-23.2 SETTING UP THE MMAC-M8FNBThe following sections list the steps necessary to set up your MMAC-M8FNB, including installing t

MMAC-M8FNB SETUPPage 3-3Figure 3-1. Installing the M8FNB into a Rack7. Align the slots on each mounting bracket with the desired holes on the equipmen

MMAC-M8FNB SETUPPage 3-43.2.2 Rack Mounting the Cable Tie TrayA cable tie tray is provided with the MMAC-M8FNB to support and organize cables connecte

MMAC-M8FNB SETUPPage 3-53.2.3 Inserting the Fan TrayThe MMAC-M8FNB is equipped with a removable fan tray that allows for easy periodic cleaning and/or

MMAC-M8FNB SETUPPage 3-6Figure 3-3. Inserting the Fan Tray3.2.4 Installing the Power Supply ModuleYou must install at least one power supply module in

MMAC-M8FNB SETUPPage 3-7The MMAC-M8FNB power supply modules are installed in the slots in the rear of the MMAC-M8FNB chassis (Figure 3-4). If you inte

MMAC-M8FNB SETUPPage 3-84. Slide the power supply into the appropriate slot of the MMAC-M8FNB as follows:a. Hold the module by the two handles on its

MMAC-M8FNB SETUPPage 3-93.2.5 Installing the Security BarsThe MMAC-M8FNB is equipped with security bars to prevent unauthorized access to the hub and

ii FCC NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause

MMAC-M8FNB SETUPPage 3-10Figure 3-5. Installing the Security Bars3.2.6 Powering Up the MMAC-M8FNBPower up the MMAC-M8FNB as follows:1. If the MMAC-M8F

MMAC-M8FNB SETUPPage 3-113. For any installed M8PSM-EDC power supplies:a. To connect to a positive 48 volt power source:1.) Connect the ground termina

MMAC-M8FNB SETUPPage 3-126.) Move the power switch on each power supply to the ON position.4. Make sure that the Power OK LED is lit.5. Make sure that

iii VCCI NOTICE This equipment is in the 1st Class Category (information equipment to be used in commercial and/or industrial areas) and conforms to

iv

v CONTENTS CHAPTER 1 INTRODUCTION 1.1 USING THIS MANUAL...1-11.1.1 Symbols...

CONTENTS vi

Page 1-1 CHAPTER 1INTRODUCTION The MMAC-M8FNB™ Multi Media Access Center offers maximum flexibility and convenience in the design and operation of y